cortexlab103
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
cortexlab103 [2018/03/26 15:34] – [What's next ?] lcardoso | cortexlab103 [2018/03/30 09:57] – [Example scenario] mimbert | ||
---|---|---|---|
Line 22: | Line 22: | ||
##Setup | ##Setup | ||
- | The purpose of this tutorial is to receive an ongoing OFDM transmission on a given USRP node. One transmitter node is set up to the whole groupe | + | The purpose of this tutorial is to receive an ongoing OFDM transmission on a given USRP node. One transmitter node is set up for the whole group and each group will control a receiver node. Instead of starting from an empty project, we are going to use the GNU Radio examples for an OFDM transmitter and receiver. We are also going to change the '' |
### Start you virtual FIT/ | ### Start you virtual FIT/ | ||
Line 129: | Line 129: | ||
# Time after which the experiment is forced to stop | # Time after which the experiment is forced to stop | ||
# | # | ||
- | duration: | + | duration: |
# Node list | # Node list | ||
Line 144: | Line 144: | ||
</ | </ | ||
- | This file uses the yaml syntax and is self-documented. | + | This file uses the yaml syntax and is self-documented. |
+ | |||
+ | Don't forget to change the node number to the node attributed to your group. | ||
### Adapting the example scenario | ### Adapting the example scenario | ||
Line 200: | Line 203: | ||
For the purposes of this tutorial, a shared reservation has been done in advance. This parent reservation' | For the purposes of this tutorial, a shared reservation has been done in advance. This parent reservation' | ||
- | To reserve your nodes in the FIT/ | + | To reserve your nodes in the FIT/ |
< | < | ||
- | tuto# | + | tuto# |
</ | </ | ||
Line 216: | Line 219: | ||
To submit a task to the scheduler, use the Minus CLI: | To submit a task to the scheduler, use the Minus CLI: | ||
< | < | ||
- | you@srvairlock: | + | tuto#@srvairlock: |
</ | </ | ||
Line 226: | Line 229: | ||
You can check the status of your experiment through the testbed scheduler. To do so, use the Minus CLI: | You can check the status of your experiment through the testbed scheduler. To do so, use the Minus CLI: | ||
< | < | ||
- | you@srvairlock: | + | tuto#@srvairlock: |
num total tasks: | num total tasks: | ||
num tasks waiting: 0 | num tasks waiting: 0 | ||
Line 236: | Line 239: | ||
The information given by this command enables you to deduce your experiment status. It's quite self-explanatory. | The information given by this command enables you to deduce your experiment status. It's quite self-explanatory. | ||
+ | __Are you having problems with your task? '' | ||
- | Once it's finished (we have set the duration to 2 minutes), Minus will take care of copying the results and output messages back to your home folder in srvairlock, so that you can analyze it. | + | ## Checking the results |
+ | |||
+ | Once it's finished (we have set the duration to 2 minutes), Minus will take care of copying the results and output messages back to your home folder in srvairlock, so that you can analyze it. | ||
+ | |||
+ | __For readability, | ||
All results are stored by task number in the results folder, inside your home folder. | All results are stored by task number in the results folder, inside your home folder. | ||
Line 243: | Line 251: | ||
Go in this folder : | Go in this folder : | ||
< | < | ||
- | you@srvairlock: | + | tuto#@srvairlock: |
- | you@srvairlock: | + | tuto#@srvairlock: |
task_15 | task_15 | ||
- | you@srvairlock: | + | tuto#@srvairlock: |
- | you@srvairlock: | + | tuto#@srvairlock: |
node4.tgz | node4.tgz | ||
</ | </ | ||
Line 254: | Line 262: | ||
< | < | ||
- | you@srvairlock: | + | tuto#@srvairlock: |
- | you@srvairlock: | + | tuto#@srvairlock: |
node4 node4.tgz | node4 node4.tgz | ||
- | you@srvairlock: | + | tuto#@srvairlock: |
- | you@srvairlock: | + | tuto#@srvairlock: |
rx_ofdm.grc | rx_ofdm.grc | ||
rx_ofdm.py | rx_ofdm.py | ||
Line 271: | Line 279: | ||
< | < | ||
- | you@srvairlock: | + | tuto#@srvairlock: |
</ | </ | ||
Line 336: | Line 344: | ||
INFO: Parser returned #f | INFO: Parser returned #f | ||
</ | </ | ||
- | |||
cortexlab103.txt · Last modified: 2018/03/30 09:58 by mimbert